TA-3 |
A universal weather radar test panel that includes a gyro simulator,
descrete test jacks for common signals as well as specific test jacks for RDS series
radar. |
TA-5 |
A complete NAV/LOC/GS test panel designed around the Collins VIR 30/31/32
series units. Requires channeling source. Combining the TA-6 panel with this
setup willprovide a total NAV panel solution. |
TA-6 |
A universal master HDG/OBS select panel with heading transmitter, TO,FR
meter and track selector. Panel requires customer supplied RMI. |
TA-14 |
A Directional Gyro test panel built around the Sperry C14 series gyro.
Panel includes a standard flux valve simulater. |
TA-55 |
Radar altimeter test panel built around the Collins ALT 50/55 system.
Stand alone capability is provided for testing indicators only, and a 4 digit DVM. |
TA-241 |
Sperry test panels (breakout) for testing their air data computers, built
to spec with some additional features. |
TA-256 |
Test Panel designed for testing and calibration of the King K1256/258
attitude gyro. This panel was layed out to King's specs and provides all the test points
needed. Includes FD board. |
TA-300 |
A vertical gyro test panel built to support the 332-D11 and VG-206.
Includes one TA-900 API. |
TA-400 |
A universal ADI test panel with meter drive capability and a unique
synchro transmitter autorate circuit providing up to 355 deg/sec rate of change. |
TA-500 |
Designed for primarily the EDO NSD-360 HSI system and provides one
capability to run the entire system. This panel is a versitile enough to be used for
testing any of the lower end HSI's on the market. The built-in API may also be used
separately from the panel. |
TA-568 |
ARINC 568 DME Generater designed to provide the instrument shop with a
digital DME source for HSI testing. This unit has an optional label changer also to
simulate various ARINC 561 standards. Fully HSI-85 compatible. |
TA-600 |
A small microprocessor based altitude decoder packaged in the same
enclosure as our TA-900. Designed with the same proven interface as the RCD-200 to give
you tracking rates of up to 20,000 FPM . All data is displayed on a two line dot matrix
display and incorprates an RS232 output. |
TA-605 |
A rack mounted TA-600 which provides additional breakouts for each code
line as well as additional switching. |
TA-900 |
Four digit digital angle position indicater with built in test capability
will insure the most reliable and accurate angle. This unit is all solid state and is
designed without the typical costly transformers. |
TA-901 |
Digital API built around the TA-900 and microprocessor based with RS232
and D/A outputs. Display resolution of 5 or 6 digits is available. |
TA-1000 |
ARINC HSI tester designed to provide full capability of testing all the
features of your HSI. This panel was designed around the Collins HSI-85 to insure that the
required simulation is present. This panel has two master transmitters and two A.P.I.'s as
well as an interface for the TA-568. |
TA-1001 |
Rack mount dual API and dual synchro transmitter (Bowmar) drives in a 19
inch rack mount configuration. Excellent addition to any shop. |
TA-1070 |
RMI panel built to duplicate the Collins Radio 970E-1 tester.
Including some additional features: one of which is an interface to our
TA-586 so when testing the BDI-36 unit a DME function is also available. This panel has
both SIN/COS and standard 3-wire outputs. And a TA-900 API can be used to verify
Bootstrap and other synchro devices. |
RCD-200 |
Channeling decoder/altitude decoding tester for verifying control heads,
altimeters and digitizers in a matter of minutes. The RCD-200 will insure proper
wafer switch alignment on Com/Nav, Descrete control heads and Cessna 1000 series. |
Model LVPS |
Low Voltage dual to quad output power supply (+15 -15 +10 and +5 volts dc)
Usable for a variety of needs. Also on board is a low level Meter Drive circuit, an
Undedicated 2 pole relay, sine/cosine oscillator and a small "breadboard" area. |
KI256 RATE BD |
Rate board built to Allied/Signal specifications per service aid
KI256/KG258-103 |
|
|